Silent Hill Downpour [BLUS30565]

I also recommend to disable FXAA smoothing and DynamicPS3ResolutionChange in coalesced_int.bin file (it's inside of SHGame/CookedPS3/ folder)

i open coalesced_int.bin but cant find those entry FXAA smoothing and DynamicPS3ResolutionChange latest build any tweaks to add them manually or something
thanks

How did you guys get it to work? It freezes for me at the start of the first cutscene on v0.0.3-6474

https://yadi.sk/d/ouPqCGki3P7JoZ
Here is the fix for this game which includes fixed movies (allows you to pass game through without removing them), fixed resolution (pure 720p instead of upscaled 576p) and FPS and optimal brightness to avoid too bright graphics.
Extract archive into emulator's dev_hdd0\game\<BLUS30565 or BLES01446>\USRDIR\ replacing existing files.

i open coalesced_int.bin but cant find those entry FXAA smoothing and DynamicPS3ResolutionChange latest build any tweaks to add them manually or something

This fix will help you too as it's already included this edited file.

Thank you kindly for the reply. I'll give it a shot

How did you guys get it to work? It freezes for me at the start of the first cutscene on v0.0.3-6474

https://yadi.sk/d/ouPqCGki3P7JoZ
Here is the fix for this  game which includes fixed movies (allows you to pass game through without removing them), fixed resolution (pure 720p instead of upscaled 576p) and FPS and optimal brightness to avoid too bright graphics.
Extract archive into emulator's dev_hdd0\game\<BLUS30565 or BLES01446>\USRDIR\ replacing existing files.

Thanks for the fix, especially for bypassing the game after the first cutscene and increasing the FPS, but I didn't see much difference for resolution and brightness..
The game (US ver: BLUS30565) is playable as I just completed it using v0.0.4-6869 (223f17a) with only minor fps-drops, shadow and lighting issues..
FYI, my spec is i7-7700, GTX-1070, 32GB-DDR4-SODIMM, 1TB-NVME-SSD..

hello
how fix this graphical issue



thanks

hello
how fix this graphical issue

If you use Resolution scaling, set it only to multipled values relating to original, e.g. 200%, 300%, 400%, and Scale Threshold set to 256x256. This will significantly reduce these kinds of artifacts. Or just disable Scaling at all by enabling Strict Rendering Mode.

The above issue isn't caused by resolution scaling it was a regression with some of kd-11s changes back in November. (pretty sure they're fixed now?) Using Intiger numbers for resolution scaling is good but a lot of games actually have graphical issues with say text being cut off unless you use a low threshold (generally 16x16 is good rather than the current default 128x128).


In preparation for upcoming changes to the compatibility database, this thread is being moved to Playable. Due to other threads for the same media (Disc or PSN) already being in that category.

If you find a specific game ID that performs differently than others for the same game+edition of the same format (PSN or Disc) even when tested with the same build and settings then please discuss it in the relevant thread(s) and PM a moderator so we can look into it.

Tested with: RPCS3 v0.0.3-3-b3efa75 Alpha

I have a problem , in the prison I have to push down a beam to create a ledge, I have to mash x but no matter how many times I push the button it won't do anything and I exit the scene after a few seconds, basically I'm stuck, I can't progress in the game, I'm using a ps4 controller, and I have about 6 FPS when I try to push it, I think this may be the cause, I usually have around 15-25 FPS in the game, I tried all kinds of setting to improve the fps but no matter what I always have around 5-6 fps, does anyone have a save file just past this point? or a solution to the problem? btw I'm running the latest rpcs3 and the latest firmware from sony

I have a problem , in the prison I have to push down a beam to create a ledge, I have to mash x but no matter how many times I push the button it won't do anything and I exit the scene after a few seconds, basically I'm stuck, I can't progress in the game, I'm using a ps4 controller, and I have about 6 FPS when I try to push it, I think this may be the cause, I usually have around 15-25 FPS in the game, I tried all kinds of setting to improve the fps but no matter what I always have around 5-6 fps, does anyone have a save file just past this point? or a solution to the problem? btw I'm running the latest rpcs3 and the latest firmware from sony

Give pc specs and configurations of rpc3

I have a problem , in the prison I have to push down a beam to create a ledge, I have to mash x but no matter how many times I push the button it won't do anything and I exit the scene after a few seconds, basically I'm stuck, I can't progress in the game, I'm using a ps4 controller, and I have about 6 FPS when I try to push it, I think this may be the cause, I usually have around 15-25 FPS in the game, I tried all kinds of setting to improve the fps but no matter what I always have around 5-6 fps, does anyone have a save file just past this point? or a solution to the problem? btw I'm running the latest rpcs3 and the latest firmware from sony

Give pc specs and configurations of rpc3

i5 6400 2.7 ghz, 8 gb ram, nvidia gtx 950, win 10 x64

ppu decoder recompiler llvm
spu decoder recompiler asmjit
firmware load only livlv2
additional settings all checked
preferred spu threads 4
renderer vulkan
aspect ratio 16:9
framelimit off
anisotropic filter disabled
the rest of the setting are the default ones